最响亮的母带峰值限制器Xilentch XMLimiter 2 v2.0.0 [WiN]

MOCHA | 19 October 2026 | 22.3 MB

XMLimiter 2——世界上最透明、最响亮的母带峰值限制器

。XMLimiter 2 并非传统的前瞻式限制器，它不依赖于诸如 Attack 或 Release 之类的时间常数参数。

相反，XMLimiter 2 像侦探一样，时刻监控并读取您的整个信号。

这种原子级的跟踪使我们能够实现最重要的一点：完全消除动态抑制、立体声窄化、瞬态模糊和抽吸效应……只有透明的限制。

话虽如此，我们也必须说明：根据源素材的不同，一些反应是不可避免的。例如，某些独奏乐器（如钢琴）的反应可能有所不同。您的某些 808 鼓机或低音乐器可能表现完美，而另一些则可能失真。这完全取决于素材本身。

然而，我们在测试阶段从支持我们的音频工程师那里得到的反馈，帮助我们意识到一个重要的问题：如果您将 XMLimiter 2 用作主输出的最终限制器，并且在推至所需电平时在某些点听到失真，则很可能是您的混音阶段存在问题。

在这种情况下，我们建议在 XMLimiter 2 之前放置一个均衡器，并进行必要的平衡调整。当然，您也可以根据自己的喜好使用——一切由您决定。OS

按钮
：默认情况下，x16 过采样已启用。这种出色的滤波器类型是我们最新的技术之一。我们建议在母带处理期间保持启用状态。对于单个音轨，可以将其禁用。

在此阶段，ISP（采样间峰值）保护功能仍然有效。但是，dBTP 则有所不同。我们不想为了追求“真实峰值”而牺牲信号透明度或增加额外的处理负担。FC

按钮：
FC 代表最终上限阶段。如果您未使用串行限制器，我们建议始终保持启用状态。否则，峰值点可能会溢出。

如果您正在使用串行限幅器，请将其禁用，让 XMLimiter 2 在中间信号链中发挥作用。

但我们也应该指出，FC 级是独一无二的。它是我们专门为 XMLimiter 2 开发的，旨在捕捉过冲信号。LINK

按钮
位于两个旋钮之间。启用 LINK 后，您可以同时向相反方向调节输入和输出旋钮，从而帮助您保持整体电平的平衡。

XMLimiter 2 – The World’s Most Transparent and Loudest Mastering Peak Limiter

XMLimiter 2 is not a classic look-ahead limiter. It does not rely on time-constant parameters such as Attack or Release.

Instead, XMLimiter 2 watches and reads your entire signal like a detective – at every single moment.

This atomic-level tracking allowed us to achieve one thing above all else: no sense of dynamic suppression, no stereo narrowing, no transient smearing, no pumping… Just transparent limiting.

That said, we should be clear: depending on the source material, some reaction is unavoidable. For example, certain solo instruments such as piano may respond differently. Some of your 808s or sub-bass instruments may work perfectly, while others may distort. This depends entirely on the material.

However, the feedback we received from the audio engineers who supported us during the beta phase helped us realize something important: if you place XMLimiter 2 as the final limiter on your master output and you hear distortion at certain points while pushing to your desired level, then there is likely a problem in your mixing stage.

In that case, we recommend placing an EQ right before XMLimiter 2 and applying the necessary balancing. Or use it however you want – the choice is yours.

OS Button
By default, x16 oversampling is enabled. This outstanding filter type is one of our latest technologies. We recommend keeping it enabled during mastering. For individual tracks, it can remain disabled.

At this stage, ISP – Inter-Sample Peak – protection is maintained. However, dBTP is a different matter. We did not want to compromise signal transparency or add extra processing load in the name of “True Peak.”

FC Button
FC stands for the Final Ceiling stage. If you are not using serial limiting, we recommend keeping it enabled at all times. Otherwise, peak points may escape.

If you are using serial limiting, disable it and let XMLimiter 2 do its job within the intermediate signal chain.

But we should also point out that the FC stage is unique. We developed it specifically for XMLimiter 2. It is designed to catch overshoots.

LINK Button
The LINK button is located between the two knobs. When enabled, LINK allows you to adjust the Input and Output knobs in opposite directions at the same time, helping you maintain a balanced overall level.